Chemical Composition | Mechanical Properties | |||||||||||||||
Tensile Strength | Impact Test | Yield Strength | Elongation In | Hardness | ||||||||||||
CS:Carbon AS:Alloy Steel | ||||||||||||||||
SPECIFICATION | TYPE | C% | Mn% | P% | S% | Si% | Cr% | Cu% | Mn% | Ni% | Va% | Mpa | 50°f 40x10 | MPA | 50mm | |
Longl | ||||||||||||||||
Standard Specification of Carbon Steel Seamless Tubes/Pipes for Steam,Water Gas and Air lines | ||||||||||||||||
ASTM A53/A | CS | 0.25MAX | 0.95MAX | 0.05MAX | 0.045MAX | - | 0.4MAX | - | 0.15MAX | - | 0.08MAX | 330MIN | - | 205MIN | 33 | - |
ASTM A53/B | 0.30MAX | 1.2MAX | 0.05MAX | 0.045MAX | - | 0.4MAX | - | 0.15MAX | - | 0.08MAX | 415MIN | - | 240MIN | 29.5 | - | |
Standard Specification of Carbon Steel Seamless Tubes/Pipes for High Temperature Services | ||||||||||||||||
ASTM A106/A | CS | 0.25MAX | 0.27-0.93 | 0.035MAX | 0.035MAX | 0.10MIN | 0.40MAX | 0.4MAX | 0.15MAX | 0.4MAX | 0.08MAX | 330MIN | - | 205MIN | 35 | - |
ASTM A106/B | 0.30MAX | 0.29-1.06 | 0.035MAX | 0.035MAX | 0.10MIN | 0.40MAX | 0.4MAX | 0.15MAX | 0.4MAX | 0.08MAX | 415MIN | - | 240MIN | 30 | - | |
ASTM A106/C | 0.35MAX | 0.29-1.06 | 0.035MAX | 0.035MAX | 0.10MIN | 0.40MAX | 0.4MAX | 0.15MAX | 0.4MAX | 0.08MAX | 485MIN | - | 275MIN | 30 | - | |
Standard Specification for Carbon Steel Seamless Tubes/Pipes for Heat Exchanger and Condensers | ||||||||||||||||
ASTM A179 | CS | 0.06-0.18 | 0.27-0.63 | 0.035 | 0.058 | - | - | - | - | - | - | - | - | - | - | 72HRBMAX |
Standard Specification for Carbon Steel Seamless Boiler Tubes/Pipes for High Pressure Services | ||||||||||||||||
ASTM A192 | CS | 0.06-0.18 | 0.27-0.63 | 0.035MAX | 0.035MAX | 0.25MAX | - | - | - | - | - | - | - | - | - | 77HRBMAX |
Standard Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater Tubes | ||||||||||||||||
ASTM A209/T1 | AS | 0.10-0.20 | 0.30-0.80 | 0.045 | 0.045 | 0.10-0.50 | - | - | 0.44-0.65 | - | - | 380MIN | - | 205MIN | 30 | 80HRBMAX |
ASTM A209/T1a | 0.15-0.25 | 0.30-0.80 | 0.045 | 0.045 | 0.10-0.50 | - | - | 0.44-0.65 | - | - | 365MIN | - | 195MIN | 30 | 81HRBMAX | |
ASTM A209/T1b | 0.14MAX | 0.30-0.80 | 0.045 | 0.045 | 0.10-0.50 | - | - | 0.44-0.65 | - | - | 415MIN | - | 220MIN | 30 | 77HRBMAX | |
Standard Specification for Seamless Carbon Boiler and Superheater Tubes | ||||||||||||||||
ASTM A210/A1 | CS | 0.27MAX | 0.93MAX | 0.035MAX | 0.035MAX | 0.10MIN | - | - | - | - | - | 425MIN | - | 255MIN | 30 | 79HRBMAX |
ASTM A210/C | 0.35MAX | 0.29-1.06 | 0.035MAX | 0.035MAX | 0.10MIN | - | - | - | - | - | 485MIN | - | 275MIN | 30 | 89HRBMAX | |
Standard Specification for Seamless Carbon Boiler and Superheater Tubes | ||||||||||||||||
ASTM A213/T2 | AS | 0.10-0.20 | 0.30-0.61 | 0.025 | 0.025MAX | 0.10-0.30 | 0.50-0.81 | - | 0.44-0.65 | - | - | 415MIN | - | 205MIN | 30 | 85HRBMAX |
ASTM A213/T5 | 0.15MAX | 0.30-0.60 | 0.025 | 0.025MAX | 0.50MAX | 4.0-6.0 | - | 0.45-0.65 | - | - | 415MIN | - | 205MIN | 30 | 85HRBMAX | |
ASTM A213/T9 | 0.15MAX | 0.30-0.60 | 0.025 | 0.025MAX | 0.25-1.0 | 8.0-10.0 | 0.9-1.10 | |||||||||
ASTM A213/T11 | 0.05-0.15 | 0.30-0.60 | 0.025 | 0.025MAX | 0.50-1.0 | 1.0-1.5 | - | 0.44-0.65 | - | - | 415MIN | - | 205MIN | 30 | 85HRBMAX | |
ASTM A213/T12 | 0.05-0.15 | 0.30-0.61 | 0.025 | 0.025MAX | 0.50MAX | 0.80-1.25 | - | 0.44-0.65 | - | - | 415MIN | - | 205MIN | 30 | 85HRBMAX | |
ASTM A213/T22 | 0.05-0.15 | 0.30-0.60 | 0.025 | 0.025MAX | 0.50MAX | 1.9-2.6 | - | 0.87-1.13 | - | - | 415MIN | - | 205MIN | 30 | 85HRBMAX | |
Standard Specification for Seamless Carbon Steel pipes for Low Temp Services | ||||||||||||||||
ASTM A333/1 | CS | 0.30MAX | 0.40-1.06 | 0.025 | 0.025 | - | - | - | - | - | - | 380MIN | 50*f | 205MIN | 35 | - |
ASTM A333/6 | 0.30MAX | 0.29-1.06 | 0.25 | 0.025 | 0.10MIN | - | - | - | - | - | 415MIN | 50*f | 240MIN | 30 | - | |
Standard Specification for Seamless Carbon and Alloy Steel Tubes for Low-Temperature Services | ||||||||||||||||
ASTM A334/1 | CS | 0.30MAX | 0.40-1.06 | 0.025 | 0.025 | - | - | - | - | - | - | 380MIN | J14 | 205MIN | 35 | 85HRBMAX |
ASTM A334/6 | 0.30MAX | 0.29-1.06 | 0.025 | 0.025 | 0.10MIN | - | - | - | - | - | 415MIN | J14 | 240MIN | 30 | 90HRBMAX | |
Standard Specification for Seamless Ferrite Alloy-Steel Pipes for Low-Temperature Services | ||||||||||||||||
ASTM A335/P1 | AS | 0.10-0.20 | 0.30-0.80 | 0.025 | 0.025 | 0.10-0.50 | - | - | 0.44-0.65 | - | - | 380MIN | - | 205MIN | 30 | - |
ASTM A335/P2 | 0.10-0.20 | 0.30-0.61 | 0.025 | 0.025 | 0.10-0.30 | 0.50-0.81 | - | 0.44-0.65 | - | - | 380MIN | - | 205MIN | 30 | - | |
ASTM A335/P5 | 0.15MAX | 0.30-0.60 | 0.025 | 0.025 | 0.50MAX | 4.00-6.00 | - | 0.45-0.65 | - | - | 415MIN | - | 205MIN | 30 | - | |
ASTM A335/P11 | 0.05-0.15 | 0.30-0.60 | 0.025 | 0.025 | 0.50-1.00 | 1.00-1.50 | - | 0.44-0.65 | - | - | 415MIN | - | 205MIN | 30 | - | |
ASTM A335/P12 | 0.05-0.15 | 0.30-0.61 | 0.025 | 0.025 | 0.50MAX | 0.80-1.25 | - | 0.44-0.65 | - | - | 415MIN | - | 205MIN | 30 | - | |
ASTMA335/P22 | 0.05-0.15 | 0.30-0.60 | 0.025 | 0.025 | 0.50MAX | 1.90-2.60 | - | 0.87-1.13 | - | - | 415MIN | - | 205MIN | 30 | - | |
Standard Specification for Seamless Carbon and Alloy Steel Tubes for Boiler and Superheater | ||||||||||||||||
BS3059/1/320 | CS | 0.16MAX | 0.30-0.70 | 0.04 | 0.04MAX | 0.10-0.35 | - | - | - | - | - | 320-480 | - | 195MIN | 25 | - |
BS3059/2/360 | CS | 0.17MAX | 0.40-0.80 | 0.035 | 0.035 | 0.10-0.35 | - | - | - | - | - | 36500 | - | 235MIN | 24 | - |
BS3058/2/440 | AS | 0.12-0.18 | 0.90-1.20 | 0.035 | 0.035 | 0.10-0.35 | - | - | - | - | - | 440-580 | - | 245MIN | 21 | - |
BS3059/2/620 | AS | 0.10-0.15 | 0.40-0.70 | 0.03 | 0.03 | 0.10-0.35 | 0.70-1.10 | - | 0.45-0.65 | - | - | 460-610 | - | 180MIN | 22 | - |
Standard Specification for Seamless Alloy Steel Tubes for Boiler,Pipelines,Pressure Vessel for Tempreature upto 600℃ | ||||||||||||||||
DN/17175/ST35.8 | AS | 0.17MAX | 0.4-1.2 | 0.04 | 0.04 | 0.1-0.35 | - | - | - | - | - | 360-480 | - | 235MIN | 25 | - |
DN/17175/ST45.8 | 0.21MAX | 0.4-1.2 | 0.04 | 0.04 | 0.10-0.35 | - | - | - | - | - | 410-530 | - | 235MIN | 21 | - | |
DN/17175/15MO3 | 0.12-0.20 | 0.4-0.8 | 0.035 | 0.035 | 0.10-0.35 | - | - | 0.25-0.35 | - | - | 450-600 | - | 235MIN | 21 | - | |
DN/17175/13CM044 | 0.10-0.18 | 0.40-0.70 | 0.04 | 0.10-0.18 | 0.10-0.35 | 0.7-1.10 | - | 0.45-0.65 | - | - | 440-590 | - | 235MIN | 22 | - | |
DN/17175/10CRMO910 | 0.08-0.15 | 0.40-0.70 | 0.035 | 0.035 | MAX0.50 | 2.0-2.5 | - | 0.90-1.2 | - | - | 450-600 | J34 | 235MIN | 20 | - |